DTP2 T 212 |
|
specification |
 |
Frame rate1 | DTP2 output 24, 25, 30, 50, 60, or 120 fps
HDMI output 24, 25, 30, 50, 60, 120, 144, or 240 fps |
Chroma sampling1 | 4:4:4, 4:2:2, or 4:2:0 |
Color bit depth1 | 8, 10, or 12 bits per color |
Signal type | HDMI 2.0b; HDCP 2.3 |
Max. video data rate | 18 Gbps (6 Gbps per color) |
NOTE | 1Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate. |
|
|
Video |
Maximum data rate | 18 Gbps (6 Gbps per color) |
Maximum pixel clock | 600 MHz |
Resolution range | Up to 2560x1600* @ 60 Hz or
4K (4096x2160) @ 60 Hz,
with 4:4:4 chroma subsampling
*reduced blanking |
Color bit depth | 8, 10, 12 bits — subject to the maximum data rate limit |
Formats | RGB and YCbCr digital video |
Standards | DVI 1.0; HDMI 1.4, 2.0b; HDCP 1.4, 2.3; CEA-861-F |
|
Video input |
Number/signal type | 2 single link HDMI (or DVI-D*) |
Connectors | 2 female HDMI type A |
NOTE | *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. |
|
|
Video output |
Connectors | 1 local HDMI output, 1 female RJ-45 output |
Horizontal frequency | 24 kHz to 135 kHz for resolutions up to 18 Gbps |
Vertical frequency | DTP2: 24 Hz to 120 Hz for resolutions up to 18 Gbps
HDMI: 24 Hz to 240 Hz for resolutions up to 18 Gbps |
Termination standard | TIA/EIA T568B |
Transmission distance | Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
Cable requirements | Solid conductor, 24 AWG or better |
Cable recommendations | 400 MHz bandwidth, STP (shielded twisted pair) |
NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
Audio |
Gain | Unbalanced output: 0 dB; balanced output +6 dB |
Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
THD + Noise | 0.03% @ 20 Hz to 20 kHz at maximum output |
S/N | >90 dB, at maximum output (15 dBu), balanced (unweighted) |
Stereo channel separation | >80 dB @ 1 kHz to 20 kHz |
|
Audio input |
Number/signal type | 1 PC level stereo, unbalanced
2 Digital Embedded Audio on HDMI |
NOTE | Analog audio can be configured for embedding onto the digital video signal at the Transmitter. Embedded digital audio can be (configured) de-embedded from the digital video signal at the Receiver end. |
|
Connectors | (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)
(2) Female HDMI |
Impedance | >10k ohms, DC coupled |
Nominal level | -10 dBV (316 mVrms) |
Maximum level | +7 dBV (unbalanced) |
NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
Communications — switcher |
Serial control port | 1 RS-232, 3.5 mm, 3-pole captive screw connector, rear panel |
Pin configuration | Pin 1 = Tx, Pin 2 = Rx, Pin 3 = GND |
Baud rate and protocol | 9600 baud, 8 data bits, 1 stop bit, no parity |
Pin configuration | Pins 1 and 2 of captive screw connector shorted together enable auto-input switching. |
USB control port | 1 female mini USB, type B, front panel |
USB standards | USB 2.0, high speed |
Contact closure/tally output | (1) 3.5 captive screw connector, 3-pole
(1) 3.5 captive screw connector, 4-pole |
Pin configuration | Contact Closure - Pin 1 =Input 1 contact, Pin 1 = Input 2 contact, Pin 2 = GND (for both captive screw) |
Pin configuration | Tally - Pin 3 = Input 1 tally ground, Pin 3 = Input 2 tally ground, Pin 4 = +5V
(on Input 2 captive screw) |
Program control | Extron Simple Instruction Set™ (SIS™) |
|
Communications — external device (RS-232/IR over TP) |
Quantity/type | (1) RS-232 and IR via (1) 3.5 mm 5-pole captive screw connector |
Serial control pass-through ports | (1) Bidirectional RS-232 |
Output/DTP Rx | (1) RS-232 (1) 3.5 mm 5-pole captive screw connector (shared with IR port) |
Baud rate and protocol | 300 to 115200 baud
8 or 7 data bits
1 or 2 stop bits
No parity (default), even or odd parity |
Serial control pin configurations | Pin 1 = Tx, Pin 2 = Rx, Pin 3 = GND |
IR control pass-through ports | (1) bidirectional TTL level (0 to 5V) modulated infrared control from 30 KHz to 60 kHz |
Output/DTP Rx | (1) RS-232 (1) 3.5 mm 5-pole captive screw connector (shared with RS-232 port) |
IR control pin configuration | Pin 3 = GND, Pin 4 = IR Tx, Pin 5 = IR Rx |
|
General |
Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 2.0 A, 24 Watts |
Power consumption | |
Device | TBD watts, 12 VDC |
Device and power supply | TBD watts, 12 VDC |
Remote power capability | Supports one endpoint (DTP2 Rx) |
NOTE | DTP2 devices can only send power to other DTP2 devices. DO NOT send power to DTP devices or they will be damaged. |
|
Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
Cooling | Convection, vents on top and sides |
Thermal dissipation | |
Device | TBD BTU/hr |
Device and power supply | TBD BTU/hr |
Mounting | |
Rack mount | Yes, with optional rack shelf
Back of the rack mountable with optional back-of-the-rack mounting kit |
Furniture mount | Yes, with optional under-desk mounting kit |
Enclosure type | Metal |
Enclosure dimensions | 1.00" H x 8.75" W x 6.0" D (1 inch high, half rack wide)
(2.54 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors.) |
Product weight | TBD lb (TBD kg) |
Regulatory compliance | CE, c-UL, UL, C-Tick, FCC Class A, ICES, RoHs, WEEE, VCCI |
Product warranty | 3 years parts and labor |
Everlast power supply warranty | 7 years parts and labor |
NOTE | All nominal levels are at ±10%. |
|
NOTE | Specifications are subject to change without notice. |
|
(5129-D8) |