DTP2 R 212 and DTP2 R 212 SA |
|
specification |
 |
Frame rate1 | |
HDMI input | 24, 25, 30, 50, 60, 120, 144, or 240 fps |
DTP2 input | 24, 25, 30, 50, 60, or 120 fps |
Chroma sampling1 | 4:4:4, 4:2:2, or 4:2:0 |
Color bit depth1 | 8, 10, 12 bits per color |
Signal type | HDMI 2.0b, HDCP 2.3 |
Max. video data rate | 18 Gbps (6 Gbps per color) |
NOTE | 1Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate. |
|
|
Video |
Maximum data rate | 10.2 Gbps (3.4 Gbps per color) |
Maximum pixel clock | 300 MHz |
Resolution range | 2560x1600 @ 60 Hz or 1080p @ 60 Hz, 12-bit color 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz 4K (4096x2160) @ 60 Hz*, UHD (3840x2160) @ 60 Hz *4:2:0 color space |
Formats | RGB and YCbCr digital video |
Standards | DVI 1.0, HDMI 2.0b, HDMI 1.4a, CEA-861F, HDCP 2.3, HDCP 1.4 |
|
Video input |
Number/signal type | 1 DTP2
1 HDMI (or single link DVI-D, with appropriate DVI-HDMI adapters) |
Connectors | 1 female RJ-45
1 female HDMI, type A |
Horizontal frequency | 15 kHz to 100 kHz |
Vertical frequency | HDMI input: 24 Hz to 240 Hz (for resolutions up to 18 Gbps)
DTP2 input: 24 Hz to 120 Hz (for resolutions up to 18 Gbps) |
|
Interconnection between transmitter and receiver |
Connectors | 1 female RJ-45 per unit |
Termination standard | TIA/EIA T568B |
Signal transmission distance | Up to 330' (100m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
Cable requirements | Solid conductor, 24 AWG or better |
Cable recommendations | 400 MHz bandwidth, STP (shielded twisted pair) |
NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
Video output |
Number/signal type | 1 HDMI output |
Connectors | 1 female HDMI, type A |
|
Audio |
Gain | Unbalanced output: 0 dB; balanced output: +6 dB |
Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
THD + Noise | 0.03% @ 20 Hz to 20 kHz at maximum output |
S/N | >90 dB, at maximum output (15 dBu), balanced (unweighted) |
Stereo channel separation | >80 dB @ 1 kHz to 20 kHz |
Bass | +12 dB to -24 dB @ 100 Hz |
Treble | +12 dB to -24 dB @ 8 Hz |
|
Audio input |
Number/signal type | |
HDMI input | 1 embedded digital audio from HDMI |
DTP/DTP2 input | 1 stereo, unbalanced analog
1 embedded digital audio from DTP |
Embedded digital audio source formats | 2-ch PCM |
Connectors | 1 female HDMI type A
1 female RJ-45 connector for audio over DTP |
Impedance | >10k ohms unbalanced, >20k ohms balanced |
Nominal level | Over DTP input: +4 dBu, -10 dBu, adjustable |
Maximum level | +15 dBu at rated THD+N when input gain is set to 0dB |
CMRR | >80 dB @ 1 KHz |
NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV≈2 dBu |
|
|
Audio output — analog (DTP2 R 212) |
Number/signal type | 1 stereo, balanced/unbalanced (fixed and variable outputs)
1 analog audio and 1 embedded digital audio on HDMI |
Connectors | (1) 3.5 mm captive screw connector, 5-pole
1 female HDMI type A |
Impedance | 50 ohms unbalanced, 100 ohms balanced |
Gain error | ±0.5 dB channel to channel |
Maximum level (Hi-Z) | >+21 dBu, balanced; >+15 dBu, unbalanced |
Output volume range | 0 to -100 dB in 1 dB steps |
Nominal level when the main volume is set to default | -2 dBu (632 mVrms) balanced output |
NOTE | 0 dBU = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
Audio output — power amplifier (DTP2 R 212 SA) |
Number/signal type | 1 stereo or 2 mono (2 channels total) |
Connector | (1) 5 mm captive screw connector, 4-pole |
Load impedance | 4 ohms, minimum |
Amplifier type | Class D |
Output power | 7.6 watts rms per channel, 8 ohms, 1 kHz, 1% THD
12.9 watts rms per channel, 4 ohms, 1 kHz, 1% THD |
Frequency response | 20 Hz to 20 kHz, +1/-3 dB @ 8 ohms |
THD + Noise | <0.1% -3 dB below clipping @ 1 kHz, 8 ohm load |
S/N | 90 dB, 20 Hz to 20 kHz, unweighted |
Damping factor | >100 @ 8 ohms |
|
Communications/remote — switcher |
Serial control port | 1 RS-232, 3.5 mm captive screw connector, 3-pole, rear panel |
Pin configuration | Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd |
Baud rate and protocol | 9600 baud, 8 data bits, 1 stop bit, no parity |
USB control port | 1 female mini-USB, type B, front panel |
USB standards | USB 2.0, high speed |
Ethernet data rate | 10/100Base-T, half/full duplex, with autodetect |
Ethernet protocol | ARP, ICMP (ping), IP, TCP, DHCP, HTTP, Telnet, SMTP |
Program control | Extron PCS®
Extron Simple Instruction Set (SIS™)
Microsoft® Internet Explorer®, Telnet |
|
Communications/remote — external device (RS-232/IR over DTP2) |
Serial control pass-through port | 1 RS-232 via 3.5 mm, 5-pole captive screw connector (shared with IR port) |
Baud rates | 300 to 115k baud |
Protocol | 8 or 7 data bits
1 or 2 stop bits
No parity (default), even or odd parity |
Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = Gnd |
IR control pass-through ports | 1 bi-directional TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz |
Output/DTP Rx | 1 RS-232, (1) 3.5 mm 5-pole captive screw connector (shared with RS-232 port) |
IR control pin configuration | 3 = Gnd, 4 = IR Tx, 5 = IR Rx |
|
General |
Power supply | |
DTP2 R 212 | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 2A, 24 watts |
DTP2 R 212 SA | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 4.2 A, 50 watts |
Power consumption | |
Device | TBD watts, 12 VDC |
Device and power supply | TBD watts, 12 VDC |
Remote power capability | |
DTP2 R 212 | Can transmit or receive power via DTP2 |
DTP2 R 212 SA | Can only transmit power via DTP2 |
Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
Cooling | Fan (air flows side to side), vents on sides |
Thermal dissipation | |
Device | TBD BTU/hr |
Device and power supply | TBD BTU/hr |
Mounting | |
Rack mount | Yes, with optional rack shelf kit
Back-of-the-rack mountable with optional back-of-the-rack mounting kit |
Furniture mount | Yes, with optional under-desk mounting kit |
Enclosure type | Metal |
Enclosure dimensions | 1.00" H x 13.1" W x 6.0" D (1" high, 3/4 rack wide)
(2.54 cm H x 33.3 cm W x 15.2 cm D)
(Depth excludes connectors)
|
Product weight | TBD lb (TBD kg) |
Regulatory compliance | CE, c-UL, UL, C-Tick, FCC Class A, ICES, RoHs, WEEE, VCCI
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply. Meets UL 60065 for safety. |
Product warranty | 3 years parts and labor |
Everlast power supply warranty | 7 years parts and labor |
NOTE | All nominal levels are at ±10%. |
|
NOTE | Specifications are subject to change without notice. |
|
(5034-D5) |