Two Output Dante Audio Interface
Key Features
  • Extracts two audio channels from a Dante® network
  • Dante audio networking with Dante Domain Manager and AES67 provides flexible connectivity
  • Mirrored two-channel analog and S/PDIF audio outputs
  • Studio grade 24-bit digital-to-analog conversion with selectable sampling rates up to 96 kHz
  • Power over Ethernet
  • Analog output is software adjustable to compensate for downstream level requirements
The Extron AXI 02 AT
Model Version Description Part #
AXI 02 AT Two Output Dante Audio Interface 60-1753-01

The Extron AXI 02 AT is a compact audio interface that extracts two channels from a Dante® audio network. This Dante Audio Interface provides two channels of audio output from the network to devices without Dante connectivity. It features two line level analog outputs on captive screw connectors with a mirrored two-channel S/PDIF output on a coaxial RCA connector. The AXI 02 AT interfaces with a Dante audio network over a standard local area network, and is powered through PoE. The AXI 02 AT includes a ZipClip® 100 Mounting Kit and is compatible with Extron Rack Shelves and ZipClip 200 mounting solutions.

Easily Provide Local or Remote Connectivity into Audio Systems

The AXI 02 AT can accept any two audio channels from a Dante network and deliver them through its two line level outputs and mirrored two-channel S/PDIF output. The analog outputs also provide adjustable attenuation, configured with DSP Configurator Software.

Dante Audio Networking

Dante enables audio system scalability over a local area network using standard Internet protocols. The family of Dante-enabled products from Extron work together as part of a complete networked audio system solution and integrate with other Dante-enabled products to create efficient, scalable system designs. They accommodate a wide range of audio routing needs in a variety of applications.

Setting up a network of Extron Dante-enabled products, including the AXI 02 AT, requires Dante Controller software. Dante Controller is used to easily assign a Dante source to an output on the AXI 02 AT.


Note: DDM and AES67 require Firmware Version 2.00.0002

  XMP 240 Dante Expansion DSP Matrix Processor
  DMP 128 FlexPlus ProDSP Dante Digital Matrix Processors
  DMP 64 Plus 6x4 ProDSP Digital Matrix Processors
  DMP 128 Plus 12x8 ProDSP Digital Matrix Processors
  DMP 128 12x8 ProDSP™ Digital Matrix Processors
  AXP 50 C AT Five Input Audio Expansion Processor with AEC and Dante
  AXP 64 C AT 6 Input, 4 Output Audio Expansion Processor with AEC and Dante
  NetPA 502 AT Two Channel Audio Power Amplifier with Dante - 50 Watts Per Channel
  NetPA 1001-70V AT Mono 70 V Audio Power Amplifier with Dante - 100 Watts
  ZipClip 200 Mounting Kit for 1/8 and 1/4 Rack Width Products
  Half Rack Shelf System Half-Rack Width Rack Shelf and Accessories
  RSB 123 Basic Rack Shelf for 3.5" Deep Products
  PMK 155 Pole and Cable Cubby 1252 MS Enclosure Mounting Kit for up to 1/2 Rack Width Products
  DSP Configurator Software DSP Application Software
  Dante Controller Configuration Software for Dante-Enabled Audio Products
  AXI 016 Sixteen Output Audio Expansion Interface


   Gain Unbalanced output: -6 dB, balanced output: 0 dB
   Frequency response 20 Hz to 20 kHz, ±0.3 dB
   THD + Noise <0.01% @ 1 kHz at maximum level
      Digital In to Analog Out >115dB, 20 Hz to 20 kHz at maximum output (unweighted)
   Crosstalk <-90 dB @ 1 kHz, fully loaded
   Output attenuation -100 dB to 0 dB (in 1 dB steps)
Audio output — analog
   Number/signal type 2 mono (or 1 stereo), balanced/unbalanced
   Connector (1) 3.5 mm captive screw connector, 6-pole
   Impedance 50 ohms unbalanced, 100 ohms balanced
   Nominal level -10 dBV (316 mV) or +4 dBu (1.23 V)
   Maximum level (Hi-Z) >+21 dBu balanced or >+15 dBu unbalanced
Audio output — digital
   Number/signal type 2 PCM (or 1 stereo)
   Connector 1 RCA connector
   Impedance 75 ohms
AT ports — audio transport
   Transmission Dante
   Connector 1 RJ-45 connector to Dante interface
   Inputs 2 channels Rx (2 flows, unicast or multicast)
   Audio format Uncompressed, 24-bit, selectable at 44.1, 48, 88.2, or 96 kHz
   Latency Deterministic, based on user selection: 1.0 ms (default), 2.0 ms, 5.0 ms
   Power input requirements Power over Ethernet (PoE 802.3af)
   PoE power injector (optional) XTP PI 100
      Power consumption 
         Device 3.2 watts
         Device and power injector 5.4 watts
   Temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling Convection, no vents
   Thermal dissipation 
      PoE power injector (optional) XTP PI 100
         Device 10.9 BTU/hr
         Device and power injector 18.3 BTU/hr
      Rack mount Yes, with optional 1U high rack shelf, with included ZipClip™ 100 mounting clip, or by securing to rack rails with tie wraps
      Furniture mount Yes, with included ZipClip™ 100 mounting clip
   Enclosure type Plastic
   Enclosure dimensions 1.62” H x 2.13” W x 4.42” D (1U high, one eighth rack wide)
(42 mm H x 55 mm W x 113 mm D)
   Product weight 0.25 lbs (0.1 kg)
   Vibration ISTA 1A in carton (International Safe Transit Association)
   Regulatory compliance 
      Safety CE, c-UL, UL
      EMI/EMC CE, C-Tick, FCC Class A, ICES, VCCI Class A
      Environmental Complies with the appropriate requirements of RoHS, WEEE
   Product warranty 3 years parts and labor
    NOTE     All nominal levels are at ±10%
    NOTE     Specifications are subject to change without notice
Shipping Dimensions and Weights
    Part # Height Width Depth Weight
    60-1753-01 2.5" (6.4 cm) 5.5" (14.0 cm) 7.0" (17.8 cm) 2.0 lbs (0.91 kg)


Panel Drawing

Panel Drawing
© 2021 Extron. Specifications are subject to change without notice.