Extron IP Intercom System Frequently Asked Questions

IP Intercom System






  1. Is the IP Intercom System a VoIP system?

    Yes. By definition, VoIP - Voice over Internet Protocol is a technology that transmits voice communication over a data network, i.e., the Internet or a corporate network. Extron's IP Intercom System is not compatible with IP Telephony systems.

  2. Is the IP Intercom System compatible with IP Telephony systems?

    Extron's IP Intercom System is not compatible with IP Telephony systems. IP Telephony systems offer the ability to carry telephone signals over a data network instead of the traditional POTS network. IP Telephony is also a VoIP system, but it uses other protocols such as H.323 or SIP defined by the International Telecommunications Union Telecommunication Standardization Sector (ITU-T) to manage the communication between handsets. IP Telephony systems provide two-way, full-duplex communications while the IP Intercom is two-way, half-duplex.

Back to Top


  1. Are IP Intercom communications secure in any way?

    Communications are encoded but not encrypted. Audio must be encoded in order to get from point A to B in the system. This product is intended for support applications and not for secure, confidential audio communications.

  2. How much network bandwidth does the IP Intercom System utilize when communicating?

    An average 80 kbps (kilobits per second) of bandwidth is used for each unicast communication between two IP Intercom Stations or between an IP Intercom Station and the help desk. When making announcements from the help desk, the bandwidth utilized is multiplied by the number of IP Intercom Stations the announcement is sent to. For instance, if the announcement is made to 10 IP Intercom Stations, the system will utilize 800 kbps of bandwidth.

  3. Is the IP Intercom compatible with all networks?

    The IP Intercom System can be integrated on all Ethernet-based networks. Sound reproduction and the quality of various other functionalities will vary depending on your network infrastructure and available bandwidth. Please contact the Extron S3 Sales and Technical Support Hotline for more information.

  4. Is there a limit to how many active IP Intercom Stations can receive an announcement from the help desk at the same time?

    This depends largely on the available bandwidth on your network. Extron recommends that you shouldn't exceed more than 25% of the total available bandwidth when making announcements. For instance, in a 100 Mbps (megabits per second) network, 25% utilization would be 25 Mbps, which allows the help desk to communicate with approximately 330 active IP Intercom Stations. This ensures that optimum sound quality is maintained. Please contact the Extron S3 Sales and Technical Support Hotline for more information.

  5. Does the specified network bandwidth of 80 kbps include the packet overhead with control or is that for audio bandwidth only?

    80 kbps includes the overhead for the VoIP packets only. Control and status monitoring of the IP Intercom is performed separately using the Telnet protocol.

  6. What transmission method does the Extron IP Intercom System use to transmit audio data?

    Unicast via UDP/IP is used to communicate between the help desk and an IP Intercom Station. When announcing to a group of IP Intercom Stations from the help desk, the message is simultaneously unicast to all selected IP Intercom Stations.

  7. Which TCP/IP protocols and standards are being used and what are they being used for?

    Telnet protocol (TCP port 23) for control and status. The VoIP traffic is sent over UDP (User Datagram Protocol) using port 3121. The auto discovery function uses UDP ports 1230 and 1231.

  8. What type of voice communication does the IP Intercom Station use over the IP network?

    Two-way, half-duplex, which means that voice data is transmitted in both directions, but not at the same time.

Back to Top


  1. Will the IPI 100 Series IP Intercom Stations work with all MediaLink Controller models?

    No. The IPI 101 AAP and IPI 104 AAP will work only with MLC 226 IP MediaLink Controllers shipped after November 16, 2005 (ER E16076 or later). You can tell if your controller supports an IP Intercom Station by looking on its back panel. If it does, it will have a second RJ-45 connector labeled "Intercom" and an audio output. For additional information, see the MLC 226 IP firmware release notes.

  2. How do the IPI 100 Series IP Intercom Stations connect to the MLC 226 IP MediaLink Controller?

    The two products connect via a CAT 5, 5e, or 6 unshielded twisted pair cable, using female RJ-45 connectors. Each IPI 101 AAP and IPI 104 AAP ships with a 12-inch (30 cm) long CAT 5 cable.

  3. How far apart can the IP Intercom Stations and the MLC 226 IP be?

    Up to 100 feet (30 meters). Instead of populating the MLC 226 IP's AAP opening, an IP Intercom Station can be installed in a separate AAP mounting frame, such as the AAP 102.

  4. Can the IPI 101 AAP or IPI 104 AAP be used without an MLC 226 IP?

    No. Those products require an MLC 226 IP MediaLink Controller for network connectivity and some intercom processing. The IPI 200 Series IP Intercom Stations are stand-alone, IP-addressable models that do not require a MediaLink Controller for operation or connectivity.

  5. What is the pinout of the RJ-45 cable used to connect the IP Intercom Stations and MLC 226 IP?

    568A or 568B. Either standard may be used as long as the pin-to-pin wiring is the same "straight-through" on both ends. This means that pin 1 of the RJ-45 plug on one end is connected to pin 1 of the plug on the other end. These connectors should be wired in accordance with the TIA/EIA 568A or TIA/EIA 568B wiring standards. The system will not work with a network crossover cable.

  6. How do I know if my MLC 226 IP will work with the IPI 101 AAP and IPI 104 AAP?

    It will work if the MLC 226 IP has the intercom RJ-45 and audio output connector. All controllers shipped after November 16, 2005 with an engineering revision number of E16076 or later are compatible with the IP Intercom System.

  7. Is there a trade-in program that would allow me to trade my older MLC 226 IP for one that supports the IP Intercom System?

    This is taken on a case-by-case basis. Contact the Extron S3 Sales and Technical Support Hotline for details.

  8. With how many locations can the IP Intercom Stations communicate?

    The IPI 101 AAP, IPI 201, and IPI 201 AAP will communicate with one location; the IPI 104 AAP, IPI 204 AAP, and IPI 204 will communicate with up to four locations.

  9. What type of warranty do the IP Intercom Stations and MLC 226 IP MediaLink Controller products carry?

    As with all powered products, Extron offers a three-year limited warranty on parts and labor for the IP Intercom Stations and MLC 226 IP MediaLink Controllers.

Back to Top


  1. What software is needed to configure the IP Intercom System?

    Extron's IP Intercom HelpDesk software has been developed for configuring and operating the IP Intercom system. All the other control and monitoring aspects of the MLC - MediaLink Controller must be configured using Extron's free Global Configurator software.

  2. How many IP Intercom Stations will the IP Intercom HelpDesk™ software support?

    The HelpDesk application establishes a Telnet connection with each connected IP Intercom Station. It really depends on how many Telnet connections the PC hosting the HelpDesk software application can support.

  3. What will happen to the network if all the IP Intercoms on campus call the same help desk location simultaneously?

    The help desk can carry on a conversation with one location at a time. If someone calls the help desk over the IP Intercom while the staff is speaking with another IP Intercom station, they will get a busy message and are placed in the HelpDesk software queue as a "Call Received" station.

  4. When using the IP Intercom HelpDesk software, can the help desk make announcements to more than one person at a time?

    Yes. The help desk operator simply picks the locations they want to make the announcement to before they begin to talk. Your network bandwidth may limit the number of IP Intercom Stations you can communicate with simultaneously.

  5. Is there a software license fee for the IP HelpDesk software?

    No. This is free software application that can be installed at as many locations as needed.

  6. Will the IP Intercom System work with GlobalViewer®?

    Yes, if GlobalViewer has been loaded into the MLC 226 IP. The IP Intercom HelpDesk software provides a hyperlink that connects the help desk operator to the GlobalViewer Web page for the MLC 226 IP that originated the call. If GlobalViewer has not been loaded into the MLC 226 IP, then the help desk operator will see the standard embedded Web page inside the MLC 226 IP.

  7. Can the IP Intercom System be configured with Global Configurator?

    The IP intercom System cannot be configured with Global Configurator. Ip Intercom Systems are configured and managed using IP Intercom HelpDesk software.

  8. Can each room be given a unique name in the IP HelpDesk software instead of using an IP address?

    Yes. Within the HelpDesk software, each room can be given a unique name.

  9. Can a Global Configurator 2.x project file be used during manual configuration of the IP Intercom System?

    Yes. Importing the Global Configurator 2.x project file will populate the IP Intercom HelpDesk software listing of MLC 226 IP MediaLink Controllers with connected IP Intercom Stations.

Back to Top