AXI 22 AT New

2 Input, 2 Output Audio Expansion Interface with Dante
Key Features
  • Two mic/line inputs for transmitting audio to a Dante® network
  • Two line level outputs receive audio from a Dante network
  • Dante audio networking provides a wide range of expansion options
  • Studio grade 24-bit analog-to-digital and digital-to-analog converters with selectable sampling rates up to 96 kHz
  • Input select, gain, and phantom power controls located on front panel and configurable through DSP Configurator Software
  • Power over Ethernet allows the AXI 22 AT to receive power over a single Ethernet cable, eliminating the need for a local power supply
The Extron AXI 22 AT
Model Version Description Part #
AXI 22 AT 2 In, 2 Out Audio Expansion Interface with Dante 60-1627-01

The Extron AXI 22 AT is a quarter rack width audio interface for integrating two mic/line sources onto a Dante®-enabled audio system. It features two mic or line inputs on a 3.5 mm captive screw connector, with switchable 48 volt phantom power. Input select, gain, and phantom power settings are controllable from the front panel, via DSP Configurator Software, or by SIS commands via USB. The AXI 22 AT also features two line level outputs for routing any two Dante channels from the network to the audio system. The AXI 22 AT interfaces with any Dante-equipped audio processor, such as an Extron DMP 128 Plus C AT, over a standard local area network, and can be powered through PoE. This allows a single network cable connection for bidirectional audio and power from a central equipment rack.

Easily Provide Local or Remote Connectivity into Audio Systems

The AXI 22 AT accepts two analog mic/line sources, and digitizes them at 24-bit for output via Dante. It is connected into a Dante network over Ethernet using standard IP networking protocols. This avoids the effort and expense of pulling long analog cables back to the AV rack. With its small, quarter rack form factor, the AXI 22 AT can be easily mounted under a desk, in a lectern, or in millwork, as well as in a rack.

For additional integration convenience, AXI 22 AT interfaces can be remotely powered via Power over Ethernet - PoE, using Extron XTP PI 100 or XTP PI 400 power injectors, network switches equipped with PoE, or midspan PoE injectors.

The AXI 22 AT can accept any two audio channels from the Dante network and deliver them through its two line level outputs. Two channels of high quality digital audio can be routed from local or remote systems via Dante, and converted to line level analog audio.

Dante Audio Networking

Dante enables audio system scalability over a local area network using standard Internet protocols. The family of Dante-enabled products from Extron work together as part of a complete networked audio system solution and integrate with other Dante-enabled products to create efficient, scalable system designs. They accommodate a wide range of audio routing needs in a variety of applications.

Setting up a network of Extron Dante-enabled products, including the AXI 22 AT, requires Dante Controller software. Dante Controller is used to easily assign an output from an AXI 22 AT to an input on a Dante-equipped device, such as the Extron DMP 128 Plus C AT. Similarly, an output from a Dante-equipped device can be assigned to appear at one of the line level outputs on an AXI 22 AT.

Features

DANTE NETWORK PRODUCTS
  AXI 44 AT 4 Input, 4 Output Audio Expansion Interface with Dante
  AXI 22 AT D 2 Input, 2 Output Audio Expansion Interface with Dante - Decorator-Style Wallplate
  DMP 128 Plus 12x8 ProDSP™ Digital Matrix Processors
  DMP 128 12x8 ProDSP™ Digital Matrix Processors
  AXP 50 C AT Five Input Audio Expansion Processor with AEC and Dante
  AXP 64 C AT 6 Input, 4 Output Audio Expansion Processor with AEC and Dante
  NetPA 502 AT Two Channel Audio Power Amplifier with Dante - 50 Watts Per Channel
  NetPA 1001-70V AT Mono 70 V Audio Power Amplifier with Dante - 100 Watts
OPTIONAL ACCESSORIES
  PS Series Desktop Power Supply 9V, 12V, & 15V Replacement Power Supplies Featuring ZipClip™
  XTP PI 100 Power Injector for XTP and Pro Series Control Systems
  Half Rack Shelf System Half-Rack Width Rack Shelf and Accessories
  MBB 100 Back of Rack Mounting Kit
  MBU 123 Low-Profile Mount Kit for 1/8, 1/4, and 1/2 Rack Width Products
  RSB 126 Basic Rack Shelf for 6" Deep Products
  RSU 126 Universal Rack Shelf Kit for 6" Deep Products
  UTS 100 Series Under Table Shelf System
RELATED PRODUCTS
  DSP Configurator Software DSP Application Software
  Dante Controller Configuration Software for Dante-Enabled Audio Products
  AXI 016 Sixteen Output Audio Expansion Interface

Specifications

AXI 22 AT
Audio
   Gain Unbalanced output: -6 dB, balanced output: 0 dB
   Frequency response 20 Hz to 20 kHz, ±0.3 dB
   THD + Noise <0.01% @ 1 kHz at maximum output level
   S/N 
      Digital In to Analog Out 115 dB, 20 Hz to 20 kHz at maximum output (unweighted)
      Analog In to Digital Out 100 dB, 20 Hz to 20 kHz at maximum input (unweighted)
   Crosstalk <-90 dB @ 1 kHz, fully loaded
   CMRR >65 dB @ 1 kHz
   Output attenuation -100 dB to 0 dB (in 1 dB steps)
Audio input
   Number/signal type 2 mono mic/line, balanced/unbalanced
   Connectors (1) 3.5 mm captive screw connector, 6-pole
   Impedance >10k ohms, balanced/unbalanced
   Nominal level +4 dBu when level is set to 0 dB gain, adjustable from -60 dBu to +4 dBu
   Maximum level >+21 dBu (at rated THD + N) when input gain is set to 0 dB
   Equivalent input noise <-120 dBV (1 µVrms) at 40 dB gain
   Input gain adjustment 0 dB to +42 dB, 3 dB steps, adjustable per input
   Mic phantom power +48 VDC ±10%, can be switched on or off per input
    NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu; All nominal levels are at ±10%
Audio output
   Number/signal type 2 mono (or 1 stereo), balanced/unbalanced
   Connectors (1) 3.5 mm captive screw connector, 6-pole
   Impedance 50 ohms unbalanced, 100 ohms balanced
   Nominal level -10 dBV (316 mV) or +4 dBu (1.23 V)
   Maximum level (Hi-Z) >+21 dBu balanced or >+15 dBu unbalanced
AT ports — audio transport
   Transmission Dante
   Connectors 1 RJ-45 connector to Dante interface
   Inputs 2 channels Rx
   Outputs 2 channels Tx
   Sampling rate Selectable in kHz: 44.1, 48, 88.2, 96
   Latency Deterministic, based on user selection: 1.0 ms (default), 2.0 ms, 5.0 ms
General
   Power input requirements 12 VDC or Power over Ethernet (PoE 802.3at)
   Power supply (optional) External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts
   Power consumption 
      Device 4.4 watts
      Device and power supply 6.2 watts
   Power injector (PoE) XTP PI 100
      Power consumption 
         Device 5.0 watts
         Device and power injector 8.2 watts
   Temperature/humidity Storage: -40° to +158° F (-40° to +70° C)/10% to 90%, noncondensing
Operating: +32° to +122° F (0° to +50° C)/10% to 90%, noncondensing
   Cooling Convection, no vents
   Thermal dissipation 
      Power supply (optional) 
         Device 11.6 BTU/hr
         Device and power supply 35.2 BTU/hr
      Power injector (PoE) XTP PI 100
         Device 13.8 BTU/hr
         Device and power injector 24.7 BTU/hr
   Rack mount Yes, with optional 1U high rack shelf
   Furniture mount Yes, with optional under-desk mounting kit
   Enclosure type Metal
   Enclosure dimensions 1.75" H x 4.3" W x 6.0" D (1U high, quarter rack wide)
(4.5 cm H x 10.9 cm W x 15.2 cm D)
   Product weight 0.65 lbs
   Regulatory compliance 
      Safety CE, c-UL, UL
      EMI/EMC CE, C-Tick, FCC Class A, ICES, VCCI
      Environmental Complies with the appropriate requirements of RoHS, WEEE
    NOTE     All nominal levels are at ±10%
    NOTE     Specifications are subject to change without notice
(041917-D4)

Diagram




Panel Drawing

Panel Drawing
© 2017 Extron Electronics. Specifications are subject to change without notice.