| AVT 200HD |
| NOTE | The AVT 200HD does not demodulate NTSC or analog CATV signals. |
|
|
| RF video input |
|---|
| Number/signal type | 1 radio frequency (RF) |
| Connector | 1 female F connector |
| Level | ATSC: -80 dBm to -5 dBm
Cable: -62 dBm to -32 dBm |
| Impedance | 75 ohms |
| Frequency range | 54 MHz to 863 MHz |
| ATSC channels | 2-69 |
| Cable channels | 1-135 |
|
| Signal processing |
|---|
| Video | ATSC 8-VSB demodulation
64/256 QAM demodulation
MPEG2 main profile high level video decoding |
| Audio | 5.1 channel Class A Dolby® Digital audio decoding
PCM audio decoding |
|
| Video output — analog |
|---|
| Number/signal type | 1 RGBHV
1 component video
1 S-video
1 composite video |
| Connectors | 5 female BNC
3 female BNC
1 female 4-pin mini DIN
1 female BNC |
| Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0 V to 1.0 Vp-p |
| Impedance | 75 ohms |
| Scaled resolution | 480i1, 480p1, 720p2, 1080i2
1 = at 59.94 Hz, 2 = at 60 Hz |
| DC offset | ±20 mV with input at 0 offset |
|
| Video output — digital |
|---|
| Number/signal type | 1 single link HDMI with audio |
| Connector | 1 female HDMI type A |
| Scaled resolution | 480p1, 720p2, 1080i2
1 = at 59.94 Hz, 2 = at 60 Hz |
|
| Sync |
|---|
| Output type | RGBHV, bi-level and tri-level for component video |
| Output level | 2.75 V to 5.0 Vp-p for RGBHV
0.6 Vp-p for component video tri-level sync
0.3 Vp-p for component video bi-level sync |
| Output impedance | 75 ohms |
| Polarity | Negative (default) or positive, selectable |
|
| Audio — analog |
|---|
| Gain | Unbalanced output: 0 dB; balanced output: +6 dB when volume is set to 0 dB gain |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | <0.3% @ 1 kHz |
| S/N | >-100 dB @ 20 Hz to 20 kHz, unweighted |
| Stereo channel separation | >35 dB @ 1 kHz |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — analog |
|---|
| Number/signal type | 1 balanced/unbalanced stereo
1 unbalanced stereo |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole
1 pair of female RCA jacks |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Gain error | ± 0.5 dB channel to channel |
| Nominal level | -10 dBV (316 mVrms), +4 dBu (1.23 Vrms) |
| Maximum level (Hi-Z) | +6 dBV (unbalanced), +15 dBu (balanced) at 1% THD+N |
|
| Audio output — digital |
|---|
| Number/signal type | 2 S/PDIF (1 optical, 1 coaxial) |
| Formats | PCM, AC-3 (Dolby Digital 5.1) |
| Connectors | 1 TOSLINK™ fiber optic connector
1 RCA jack |
|
| Control/remote — tuner |
|---|
| NOTE | The front panel USB port and rear panel RS-232 port are independent of each other and can be used at the same time. |
|
| Serial control port | 1 bidirectional RS-232, 3.5 mm captive screw connector, 5 pole (shared with wired IR control) |
| Baud rate and protocol | 115200, 38400, 19200, or 9600 baud (default); 8 data bits; 1 stop bit; no parity |
| Serial control pin configurations | 1 = Tx, 2 = Rx, 3 = GND, 4 = modulated IR, 5 = +12 VDC |
| USB control ports | 1 front panel female mini USB B |
| USB standards | USB 2.0, low speed |
| Ethernet control port | 1 RJ-45 female |
| Ethernet data rate | 10/100Base-T, half/full duplex with autodetect |
| Ethernet protocol | ARP, ICMP (ping), IP, TCP, DHCP, HTTP, SMTP, Telnet |
| Ethernet default settings | Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Default gateway = 0.0.0.0
DHCP = off |
| Web server | Up to 200 simultaneous sessions
7.25 MB nonvolatile user memory |
| IR remote control | AVT 200HD remote (optional)
Front panel: 30' maximum, 40 degrees off axis
Rear panel captive screw connector (shared with RS-232): 38 kHz, hardwired, modulated |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set™ (SIS™)
Microsoft® Internet Explorer® ver. 6 or higher, Telnet |
| IR/serial control ports | (2) 3.5 mm captive screw connectors, 2-pole
Programmable: RS-232 (±5 V), or TTL level (0 to 5 V) infrared up to 1 MHz |
|
| General |
|---|
| Power supply | Internal
Input: 100 VAC to 240 VAC, 50-60 Hz |
| Power consumption | 25.0 watts |
| Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on top and sides |
| Thermal dissipation | 52 BTU/hr |
| Mounting | |
| Rack mount | Yes, with included brackets |
| Furniture mount | Yes, with optional mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.7" H x 17.5" W x 10.5" D (1U high, full rack wide)
(4.3 cm H x 44.4 cm W x 26.7 cm D)
(Depth excludes connectors.) |
| Product weight | 5.5 lbs (2.5 kg) |
| Shipping weight | 10 lbs (5 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10% |
|
| NOTE | Specifications are subject to change without notice. |
|
| (8.0-041312-D2) |